About this seminar
The risks of working at heights are faced by roof tilers daily.
One of the most effective ways to reduce the risks is to design the work to be conducted as much as possible at ground-level. If this cannot be done, look at ways to reduce the need to work at height.
It’s also important to conduct a pre-job assessment – preparation prevents poor performance. Make sure your crew is qualified, trained and experienced in what they will be required to do, and expectations are clear.
The video discusses what to do, and what not to do, when working at heights.
Work safe, go home safe.
Who is this seminar for?
This seminar is useful to tradies who conduct work at heights.
About the presenters
This video was produced by the Roofing Tile Association of Australia.
- Model Code of Practice: Managing the risk of falls at the workplace
- Model Code of Practice: Preventing falls in housing construction
- Safe work on roofs information sheet
- Preventing workers falling from trucks
- Safe use of ladders video
- Work related injuries and fatalities involving a fall from a height, Australia 2013
Working at Heights
§ (Music Playing) §
[Opening visual of slide text saying ‘Brought to you by Safe Work Australia Virtual Seminar Series’, seminars.swa.gov.au, ‘#virtualWHS’]
Working at heights is one of the highest risk activities across the industry, and as roof tilers we have to live with and manage that risk daily.
Here are some key things to remember when working on a roof so that we all get to go home safely every day.
Step 1, pre-job assessment. As they say, preparation and pre-starts prevent pretty poor performance. So a key to starting any job, large or small, is to go through a thorough pre-start process. As part of the pre-start, make sure your crew are qualified, trained and experienced in what they will be asked to do, and that everyone is clear on what’s expected of them that day.
Check the site for any hazards and risks that could affect you, and make sure the best controls are put in place before you start working. Also check the weather conditions for the day, because they could impact your work depending on what stage you are at on the roof.
Make sure everyone in your crew is fully aware of and familiar with the emergency response plan in case someone does fall.
On new builds, physical fall protection must be in place and secure before getting on to the roof. Remember no fall protection, no start.
If you are going to be working on a roof with a pitch that is steeper than normal, make sure the correct extra controls are in place to keep you safe. If you are not sure, check with your supervisor before getting up on the roof. One question or one quick check could save your life.
Also if you’re working on a two storey building, make sure that all openings and penetrations inside the building are securely covered.
Lastly, make sure you’ve set up a no-go zone to prevent injury to ground workers from falling materials.
Step 2, getting to and from the roof. Once you are good to go, take care as you get up on to the roof. It’s important to wear footwear with good grip, and that the treads are as clean as possible to prevent slipping.
If you’re using a ladder, make sure you use the right ladder for the height of roof you are going to be working on, and that it’s set up correctly at the right access points. If you’re not sure, ask someone, or check the Safe use of Ladders video from the Roofing Tile Association of Australia available on your phone.
Step 3, working on the roof. On new builds you’re the most exposed to the risk of falling from the roof when you’re first marking out and fixing the battens. So when you first get on the roof, check that the trusses are secure, fully braced off and safe to walk on. If trusses are wider than 600 millimetres apart, additional controls are needed, so call your supervisor for advice.
Whenever possible, walk on the bottom cord of the trusses while you’re marking and laying your battens so the trusses themselves act as fall protection for you.
While you’re fixing the battens, look out for anything wrong with the batten that could become a weak spot. Fix your battens, starting at the bottom of the roof and working your way up. This provides extra fall protection as you move higher up the roof.
As you walk around the roof, remember to only stand on the junction where the batten crosses the truss before the tiles are laid, and once the tiles are laid, stand on the tile overlap to prevent them from breaking and losing your balance.
When working near the valleys, always walk on the battens or tiles, never on the valley irons themselves because they can be very slippery when wet.
Rolling out sarking is always a two person job. Always remember to place the shiny side down, and take extra care when rolling it out. Once the tiles are laid and pointing begins, make sure you don’t overfill your bedding buckets. No more than 15 kilograms is recommended.
By remembering and following these key steps when tiling a roof, we can all go home safely every day.
§ (Music Playing) §
[Text: ‘Workers are qualified and competent’, ‘Control all hazards and risks’, ‘Walk on the bottom cord of trusses’, ‘Step only where the batten crosses the truss’, ‘Stand on the tile overlap when walking’, ‘Never walk on the valley irons’]
Think smart before you start. Keep safety in mind. It will save your behind.
§ (Music Playing) §
[Text: ‘Proudly produced for the Roofing Tile Association of Australia by CodeSafe Solutions in consultation with Safe Work Australia’]
[Closing visual of slide text saying ‘Brought to you by Safe Work Australia Virtual Seminar Series’, seminars.swa.gov.au, ‘#virtualWHS’]
[End of Transcript]
Serious injuries are an ongoing issue in the workplace. They can impose devastating impacts on workers and sometimes preclude them from ever re-entering the workforce. This infographic highlights some of the effects serious injuries have on workers.
This infographic shows research and data about the most common causes of death and serious injury in the construction industry.
Children and young people in the workplace are especially vulnerable when it comes to safety; when they enter a workplace a person conducting a business or undertaking is responsible.
Providing a mentally healthy workplace not only protects workers from psychological harm, it positively enhances their mental health and can improve business productivity.
Emergency services workers operate in challenging environments, dealing with violence, distress and often death. Since 2003 that work environment has claimed the life of 47 first responders.
This infographic is based on the latest data from worker fatalities and workers’ compensation claims, and includes statistics on the nature, circumstances and main causes of injuries and fatalities in this industry.
This infographic looks at the key factors attributed to serious claims by healthcare professionals, so that we can focus on how to reduce these statistics.
Presenting some of the key data on bullying and violence in Australian workplaces, this infographic demonstrates the connection between harassment, bullying and violence and work-related mental disorders.